ski hook

A recent conversation with a SkinTrack follower on Twitter prompted me to write this DIY/How To article. Over the years, I have owned couple of skimo racing and ski touring packs so I have a good experience with what works and what doesn’t (meaning, it works less than I would like). So let’s go.

Two good systems for fast ski attachment

In the last 10 years or so, two systems were developed allowing skimo racers to attach their skis to their backpacks without ever taking their pack off.
The first one, before ISMF rules allowed the hook system, was very secure and quickly became popular. It worked like this:

You took off your skis and put them together.
Then holding them both in one hand, you put the tails of your skis through a loop (flat webbing/sling) on the bottom right or left side of the pack.
You slid them down until the heel bindings stopped the skis in place.
You pulled the skis closer to your neck with one hand and wrapped a strong bungee cord around them once.
Then you clipped a carabiner at the end of that cord to a plastic or a metal ring that was about half-way down one of your shoulder straps (always the opposite strap to the side where the bottom loop was).

The second system, being widely used now, is the ski hook system. It is not as secure as the first one but it’s very fast. It works the same way like the above until step #4 at which point you just hook a metal hook that is attached to a strong bungee around your skis and you are done. No wrapping or clipping.
Here are photos showing the difference between the two systems:

There's a strong bungee inside that black protective sleeve. You wrapped it around and then clicked the small carabiner into a plastic ring. — There’s a strong bungee inside that black protective sleeve. You wrapped it around and then clicked the small carabiner into a plastic ring.

This is a hook system on a Dynafit Manaslu 35 backpack. Hook is at the end of a strong bungee that is attached about half-ways down on the right side shoulder strap. — This is a hook system on a Dynafit Manaslu 35 backpack. Hook is at the end of a strong bungee/elastic that is attached about half-ways down on the right side shoulder strap.

Making a ski hook system

Since the ski hook system is the more popular one let’s take a look at how you can make one for your pack. Or how you can make a new better hook if you don’t like your current one.

Bottom-side loop

A basic requirement that both above systems have in common is that you need a loop on one of the sides at the bottom of your pack. Depending on a pack you have this might be easier or more difficult to setup but at the end it should look like this:

My regular touring Dynafit 35 L backpack, on the left, uses a very ridged plastic or rubber-like loop. My current 4-years old Ortovox race pack uses just webbing which I like to wrap in colorful duct-tape so it doesn't bend — My regular touring Dynafit 35 L backpack, on the left, uses a very rigid plastic or rubber-like loop. My current 4-years old Ortovox race pack uses just webbing which I like to wrap in colourful duct-tape so it keeps the loop from collapsing and is easier to see when in a hurry.

Also, depending on the width of the skis you are planning to carry you should make this loop big enough. Tails and under-the-foot widths of skimo race skis are around 80 mm and 65 mm respectively. Widths for regular backcountry skis are hard to talk about since all of us have different preferences.
The material I recommend to use for the loop is webbing or an old sling, then wrap it in some duct-tape to make it more rigid (Gorilla tape is the most durable).

Manufacturing the ski hook

Ski hook is not a ski hook – some work great while others not well enough. So what makes a hook work well?
I discovered that if the ski hook is made from a strong, flat piece of material (2 cm wide is enough) then it works the best. And, of course, the dimensions and the way it is bend play big roles too.
Without reinventing the wheel I took my two favourite packs and took a closer look at their hooks – the way they are shaped and the dimensions they have. Surprisingly, they are very similar despite the metal pieces they are made of are totally different.
Here is how they compare:

As you can see, dimension-wise they are very similar except the width. The Ortovox hook on the right secures the skis a bit better but is also a bit bulky. — As you can see, dimension-wise they are very similar except the width. Shape-wise, from the side, they are almost the same as well. The Ortovox hook on the right secures the skis a bit better but is also a bit bulky.

For this How To tutorial I decided to make the Dynafit style ski hook since it works well with a wide variety of skis and the materials and tools needed are easier to come by.
This is what you need (or what I used):

40 cm long piece of 1/8″ (3.15 mm) thick, easy to work with yet very strong metal rod (or wire with similar properties and diameter), preferably one that will not rust.
I bought something labeled as “solid brass” which appeared easy enough to shape and apparently doesn’t rust.
Then you will need lineman’s or combination pliers,
and vice could be useful as well.

Here’s the process:
Step 1 – Dimensions

These add up to 18 cm for one end, so 36 cm in total. I went with 4 cm extra to account for the curves and curls. It worked perfectly. — These add up to 18 cm for one end/arm, so 36 cm in total. I went with 4 cm extra to account for the curves and curls. It worked perfectly.

Step 2 – Curl both ends of the rod so you don’t cut yourself. (You can use a file to smooth the ends before you curl them if you want.)

The loops will be handy for running bungee cord through them. — The curls will be handy for running a bungee cord through them.

Step 3 – Bend the rod exactly in half. I used a balcony railing to wrap the rod around and then finished it using a vice.

At the bottom, you can see that after bending the rod and curling the ends I ended up with about 18,5 cm of running length.

Step 4 – Bend the 5,5 cm part to 90 degrees using a vice because now you will be bending two rods at once.
Step 5 – To finish off, bend the 9 cm part to 90 degrees which will leave you with about 3,5 cm piece in the middle.

Since I was bending both rods at once again I started in a vice but ultimately had to finish it with my hands and pliers since I didn't have enough space in the vice to finish to 90 degrees. — Since I was bending both rods at once again I started in a vice but ultimately had to finish it with my hands and pliers since I didn’t have enough space in the vice to go to 90 degrees.

Step 6 – Maybe you should try the single rod hook first to get used to the material. I didn’t but made one at the end since some race packs use that version (which in my opinion is very wobbly).

Final thoughts on manufacturing the hook:
I believe the secret of a good ski hook is in 4 things:

Making the 90 degree bends as tight/sharp as possible,
keeping everything else as straight as possible,
making the parallel parts long enough (not obsessing about extra weight),
and making it either a double rod hook or from a flat material.

I ultimately don’t know why single rod hooks don’t work as well but it is either due to one of the following reasons or a combination of them. On some backpacks the hooks are:

either too short,
or the 2 bends are more like a one big curve,
or simply a single rod doesn’t have enough side leverage to hold the skis in place sufficiently.

Attaching bungee cord to the hook

I couldn’t find a strong/thick enough bungee at home so I used a thinner one I use for making skin attachments. (Working on that How To tutorial as well.) However, if you are just replacing your existing hook you will have some cord to work with.

I just used a figure eight know for the attachment.

As you can see above, I bent the two ends/rods of the hook away from each other based on the Dynafit ski hook. This should add your home made hook stability/leverage once wrapped around the skis. However, it would be beneficial to insert a piece of small plastic tubing in between the rod ends that would always keep them apart because if you use a softer material the ends will be pulled together once the bungee is under load.

Attaching bungee to your pack

You will need to do this if you are building a brand new carrying system on a pack, and you should not need to if you are just replacing a bad hook.
If you are building a brand new ski hook system then depending on what kind of straps, plastic or metal pieces your backpack has on its shoulder straps this will be easy or more difficult.
Important – remember to attach your cord with a hook to the opposite shoulder strap than on what side you placed your bottom-side loop. And use a strong bungee.
On the photo below, I am pretending the pack has clean, smooth shoulder straps so I am just attaching the bungee to the top of the strap to prevent it from moving once under load. It would be desirable to attach it further down the shoulder strap if you can figure out how to secure it there. Duct-tape? 🙂

Ultimately, to figure out the right length of the bungee you will need to play around a bit. My suggestion is to start with a bungee or an elastic not longer than 10-15 cm when stretched.
That should be all you need to know on how to make your own ski hook.

ski hook

How to make a ski hook for rapid backpack skis attachment?

Two good systems for fast ski attachment